SFP GPON OLT Transceiver Class D 8dBm TX Power Optical Modules DDM

GPON OLT SFP Class D TX Power 8dBm Transceiver Modules Part Number GTS-SGT21-20DCF

Description

This 8dBm Tx Power GPON OLT SFP is full compliant with ITU G.984.2 Class D/C+++ requirements for optical line terminal (OLT) applications with 1.244Gbps upstream and 2.488Gbps downstream.

This GPON D SFP packaging module consists of 1490nm continuous-mode 2.488Gbps DFB transmitter, 1310nm burst-mode 1.244Gbps APD receiver, Preamplifier and WDM filter in a high-integrated optical sub-assembly. It is a Class 1 laser Product comply with the IEC 60825-1 and IEC 60825-2, and it is MSA SFP, SFF-8472 and ROHS6 compliant.

Specification

Features

• Single fiber bi-directional data links asymmetric TX 2488Mbps/RX1244Mbps application
• 1490nm continuous-mode DFB laser transmitter and 1310nm burst-mode APD-TIA receiver
• Small Form Factor Pluggable package with SC/UPC Connector
• Operating case temperature Range:Commercial: -5°C~70°C, Industrial: -40°C~85°C
• Single 3.3V power supply
• Digital diagnostic monitoring interface
• Digital burst RSSI function to monitor the input optical power level
• LVPECL compatible data input/output interface
• LVTTL transmitter disable control
• LVTTL transmitter laser fault alarm
• Fast LVTTL receiver Signal Detect (SD) indication response
• Low EMI and excellent ESD protection
• Class I laser safety standard IEC-60825 compliant
• RoHS6 Compliance

Application

• Gigabit-capable Passive Optical Networks (GPON)

Standards

• Complies with SFP Multi-Source Agreement (MSA) SFF-8074i
• Complies with ITU-T G.984.2 Amendment 1
• Complies with FCC 47 CFR Part 15, Class B
• Complies with FDA 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007
• Complies with SFF-8472
• Compatible with TR-NWT-000870 4.1 ESD sensitivity classification Class2.
• Compatible with Telcordia GR-468-CORE

Typical Application Circuit

EEPROM Memory Map

EEPROM Serial ID Memory Contents

The optical transceiver contains an EEPROM. It provides access to sophisticated identification information that describes the transceiver’s capabilities, standard interfaces, manufacturer, and other information. When the serial protocol is activated, the host generates the serial clock signal (SCL, Mod Def 1). The positive edge clocks data into those segments of the EEPROM that are not writing protected within the SFP transceiver. The negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially.

The Module provides diagnostic information about the present operating conditions. The transceiver generates this diagnostic data by digitization of internal analog signals. Calibration and alarm/warning threshold data is written during device manufacture. Received power monitoring, transmitted power monitoring, bias current monitoring, supply voltage monitoring and temperature monitoring all are implemented. The diagnostic data are raw A/D values and must be converted to real world units using calibration constants stored in EEPROM locations 56 - 95 at wire serial bus address A2h. The digital diagnostic memory map specific data fields define as following.

Ordering information - Gigaopto’s GPON OLT SFP Series(DFB+APD TX-2.488Gbps/RX-1.244Gbps/TX-1490nm/RX-1310nm SC Simplex)